XBee® ZNet 2.5 Adapters
Features
- General
- Frequency: 2.4 GHz (ISM)
- Antenna options: Integrated whip antenna
- Performance
- Indoor/Urban range: Up to 100 ft (30 m)
- Outdoor RF line-of-sight range: Up to 300 ft (100 m)
- Transmit power output: 1 mW (0 dBm)
- RF data rate: 250,000 bps
- Receiver sensitivity: -95 dBm (1% PER)
- Networking and Security
- Network topologies: Point-to-Point, Point-to-Multipoint, Peer-to-Peer, Mesh
- Number of channels:
- 16 - 5 MHz channels (Direct Sequence Spread Spectrum)
- Filtration options:
- PAN ID, Channel, 264 (64-bit) addresses
- LEDs
- Power: Glows green when external power is supplied (not active when battery powered to limit power drain)
- Associate: Glows when unit is connected and associated on an RF network Controls
- Controls
- Device reset (internal push button)
- Identification (internal push button): Relays identification to ConnectPort X gateway
Interfaces
- Serial
- RS-232 (DB-9M)
- RS-232PH (DB-9M); power harvesting version
- RS-485 (6-position wire terminal block) - Switch selectable between RS-422 half duplex, RS-422 full duplex and RS-485
- 1-Wire Sensor (RJ-45)
- USB
- USB 2.0 Full Speed (with ESD protection); connects to host via captive 2-meter cable
Environmental
- XBee 232, 485, 1-Wire Sensor, USB, Analog I/O and Digital I/O
- Operating temperature: -40° C to 70° C
- Powering options
- Battery: -18° C to 55° C
- External power: 0° C to 40° C
- External power (hardened): -35° C to 74° C
- XBee 232PH
- Operating temperature: 0° C to 65° C
Regulatory Approvals
- FCC Part 15.247 - Pending
- Industry Canada (IC) - Pending
- Europe (CE) - Pending
- EN55022, Class A - Pending
- UL60950 - Pending
- CAN/CSA C22.2 No. 60950 - Pending
- EN60950 - Pending
- RoHS compliant
Power Requirements
- XBee 232, 485, 1-Wire Sensor, Analog I/O and Digital I/O
- Externally powered: 9-30VDC, locking connector
- Battery powered: 3 internal N cell batteries
- XBee USB
- Bus powered: +5V from USB bus
- Power consumption during normal operation:
- XBee: 70 mA
- XBee-PRO: 70 mA (Rx) and 250 mA (Tx)
- Power consumption during suspend mode:
- XBee and XBee-PRO: 200 uA
- XBee 232PH
- Internal battery provides power when unit is operating and recharges from the serial port when in sleep mode
- Requires a sleep/wake duty cycle as part of its normal operation.
- Requires a fully functional serial port conforming to the RS232C standard for optimal operation.
- Sleep/wake duty cycle requirements will vary based on the current output of serial port
- Serial ports with more than 14VDC output (rare) are not supported and may cause malfunction
- Serial ports that provide hard power of 5 to 14VDC on one or more pins will allow the device to operate continually without a sleep/wake cycle
Dimensions
- XBee 232, 485, 1-Wire Sensor, Analog I/O and Digital I/O
- Width: 1.68 in (4.26 cm)
- Height: 0.99 in (2.53 cm)
- Length: 3.87 in (9.84 cm)
- Weight: 2.29 oz (6.50 g)
- XBee USB and 232PH
- Width: 1.80 in (4.57 cm)
- Height: 0.83 in (2.10 cm)
- Length: 2.87 in (7.29 cm)
- Weight: 1.60 oz (45.36 g)
Line Art
- XBee 232, 485, 1-Wire Sensor, Analog I/O, Digital I/O
- Front/Back
- Interface Options
- Front/Back
- XBee USB, 232PH
- Back
- Interface Options
- Back