Contact us: PhonePhone EmailEmail ChatChat

XPress™ Ethernet Bridge

900 MHz wireless Ethernet bridge

  • Web interface simplifies configuration and troubleshooting
  • Frequency agility ensures reliable connection between radios
  • Spectrum analyzer for RF interference
  • Outdoor line-of-sight range up to 15 miles
  • AES encryption and FIPS 197 provide secure communication
  • Product datasheet

The XPress Ethernet Bridge replaces costly wiring with a solution that can wirelessly connect industrial PLCs, digital signs, security cameras, access controllers and more. With a range of up to 15 miles, the ability to transmit through as many as 10 standard walls, a 1.5 Mbps data rate, and the added range and capabilities of the 900 MHz band, the easy-to-use, long-range XPress Ethernet Bridge communicates where Wi-Fi and other wireless data products fall short.

 

Models North America: International:  
XPress Ethernet Bridge, Pair
View details | Related accessories
XEB09-CIPA
XEB09-CIPA-W
Buy online
Contact us
XPress Ethernet Bridge, Single
View details | Related accessories
XEB09-CISA
XEB09-CISA-W
Buy online
Contact us
Specifications XPress™ Ethernet Bridge
Performance
Indoor/Urban Range Up to 1000 ft (300 m) w/ 2.1 dB dipole antenna
Outdoor/RF Line-of-Sight Range Up to 2 miles (3.2 km) w/ 2.5 dB dipole antenna, Up to 15 miles (24 km) w/ high-gain antenna
Transmit Power Output 125 mW (+21 dBm), 4W EIRP w/ 15 dBi antenna
Throughput Data Rate 935 Kbps
RF Data Rate 1.536 Mbps
Receiver Sensitivity -97 dBm (@10e-4 BER)
Features
Browser Management Tools QoS statistics, Network settings, Spectrum analyzer, Firmware upgrading
Data Connection 10/100Base-T RJ-45, Auto MDI/MDIX
Interference Immunity DSSS (Direct Sequence Spread Spectrum)
Encryption 128-bit AES, FIPS 197/NIST certified
Radio Channels/Bandwidth 12 channels (6 in international version) with 2.0833 MHz spacing and 1.75 MHz occupied bandwidth
Frequency Band ISM 902-928 MHz (915-928 MHz international version)
Frequency Agility Radio channel automatically selected and adaptively optimized
Manual Frequency Mode Channel selected with DIP switch or web browser interface
Status LEDs Power, RF TX/RX, Ethernet link, channel, link quality
Error-Correction Technique Sub-block error detection and retransmission
Adjacent-Band Rejection >60 dB - SAW receiver filter attenuates cellular and pager interference
Regulator Type Switching regulator
Antenna Connector RF RPTNC female
PoE (Power over Ethernet) Proprietary system included
Subscriber Units Up to 16 active (63 total) per access point
Serial Number Based Mating Protocol Yes
Dimensions (L x W x H) 7.9 in x 3.6 in x 2.4 in (20.0 cm x 9.1 cm x 6.1 cm)
Weight 320 g
Power Requirements
Power Consumption Transmit: 1.7W, Receive: 0.8W
Transmit Current Draw 9 - 48VDC Power over Ethernet, 175 mA at 9VDC, 140 mA at 12VDC, 35 mA at 48VDC
Power Connector Use PoE injector, power jack P5-2.1 mm center positive
Environmental
Operating Temperature Radio/Enclosure: -40° C to +70° C; POE injector: -40° C to +85° C; Power supply: 0° C to +40° C
Weatherproofing The XPress Ethernet Bridge enclosure is built and tested for weatherproof installation. The PoE injector and power supply are not weatherproof, and should be installed indoors.
Regulatory Approvals
FCC (U.S.A) Yes
IC (Canada) Yes
ETSI (Europe) N/A
C-TICK (Australia) Yes
TELEC (Japan) N/A
 

Related Links

 

The XPress Ethernet Bridge replaces costly wiring with a solution that can wirelessly connect industrial PLCs, digital signs, security cameras, access controllers and more. With a range of up to 15 miles, the ability to transmit through as many as 10 standard walls, a 1.5 Mbps data rate, and the added range and capabilities of the 900 MHz band, the easy-to-use, long-range XPress Ethernet Bridge communicates where Wi-Fi and other wireless data products fall short.

The XPress Ethernet Bridge features a built-in spectrum analyzer, allowing users to monitor RF interference. Frequency agility enables the product to automatically select the best available radio channel at start-up, monitor the signal-to-noise ratio and move the network to a new channel if necessary. A web interface simplifies installation, allows users to monitor packet success and signal strength, and facilitates remote troubleshooting.

The XPress Ethernet Bridge is housed in a weatherproof enclosure. It is available in pre-paired units or single units for point-to-multipoint applications.

 

 

Privacy Policy | Terms & Conditions | Contact Us | Careers | Site Map | Newsletter Signup | Feedback
Copyright © 1996-2010 Digi International Inc. All rights reserved.
Facebook YouTube