Home > Support > Knowledge Base

Knowledge Base

All
Configuration: 9 result(s) found
Installation: 7 result(s) found
Hardware: 3 result(s) found
Miscellaneous: 8 result(s) found
Troubleshooting: 6 result(s) found

 

There are 17 search results for ""
What is the Non Operating (storage) temperature for Digi products?
Category: Configuration, Installation, Miscellaneous, Troubleshooting
Non Operating (Storage) Temperature is -40C to 80C (-40F to 150F) Non Operating (Storage) Humidity is 5 to 95% (non-condensing)
SuSE 8.2 RealPort Installation Instructions
Category: Installation
Preparing for the Installation: In SuSE 8.2, we had to download and install the following kernel and kernel source: ftp.suse.com/pub/suse/i386/8.2/suse/i586/kernel-source-2.4.20.SuSE-62.i586.rpm ftp://ftp.suse.com/pub/suse/i386/8.2/suse/i586/k_d...
How to Configure a Linux System Serial Port for Console Management Using Grub.
Category: Configuration
The linux box won''''''''t have console turned on by default, you will need to spawn a getty at ttyS0 (the first serial port). Here is an example of the /etc/inittab file entry: 0:12345:respawn:/sbin/agetty 9600 ttyS0 Configure /etc/grub.conf: ...
How To Install the RealPort Source RPM Driver in Mandrake Linux
Category: Installation
Installation process for installing RealPort in RedHat Be sure there are no existing RealPort drivers installed on the system. If so, please remove prior to installing newer versions. Installation preparation in Linux: Log the installation: # ...
How To Install the RealPort Source RPM Driver in SuSE Linux
Category: Installation
Installation process for installing RealPort in RedHat Be sure there are no existing RealPort drivers installed on the system. If so, please remove prior to installing newer versions (rpm -e dgrp). Installation preparation in Linux: Log the...
EIA-232 Information
Category: Hardware
DTE vs DCE This is one of the most misunderstood areas of RS-232. DTE stands for Data Terminal Equipment, and DCE stands for Data Circuit-terminating Equipment or Data Communications Equipment. The DTE is typicall...
Recommended Custom Cable Vendors
Category: Miscellaneous
The Whyte Haus 260-484-5666 the.whytehaus@verizon.net Contact: Barb Whyte   Predator Grizzly Cable (503)292-7151 x 1101 CSP, Inc. 763-475-8346 mrannals@csp.com ...
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
What is Digi International doing to comply with the RoHS requirements?
Category: Miscellaneous
Digi International is in the process of preparing to meet the RoHS requiements. For details, please visit this link:  http://www.digi.com/aboutus/environment.jsp  
When installing a Digi driver in SuSE Linux with 2.6.x kernels, a tainted kernel message is seen.
Category: Installation, Troubleshooting
As an extension to the mainline kernel, modules can be tagged as supported (directly by SUSE, or indirectly by a third party) or unsupported. Modules which are known to be flakey or for which SUSE does not have the necessary expertise are marked as u...
How do I configure my (ditty-rp) port settings to stay after rebooting when using RealPort in Linux.
Category: Configuration, Troubleshooting
In Linux the ditty settings are "sticky" until overwritten or the system is rebooted. For port configuration on the Linux host, there is a file you can create to issue the ditty commands at startup. Simply create and add your ditty commands to...
The end of my print jobs are being cut-off and never print the end of the document.
Category: Configuration, Troubleshooting
This behavior is due to the spooler closing the connection prior to the port buffer draining. The following command can be used to hold the port open so all of the data prints: # cat /dev/null & Where ttyx## represents the actual tty ...
How can I remotely manage dumb terminals attached to Digi Ethernet devices?
Category: Configuration, Miscellaneous
If you are using the network-enabled Digi products, they actually have some ability to monitor data directly, and other options may be available in addition to these suggestions. Some tools that are available if you want to implement your own so...
There is a very long delay seeing the login prompt in Solaris and UnixWare.
Category: Configuration, Troubleshooting
Customers have reported problems with ttymon handling a large amount of ports. Reportedly, adding more ttymons and only assigning 2 or 3 ports per ttymon relieves the symptoms.
How do I perform automated tasks on Digi device and terminal server units automatically without user intervention?
Category: Configuration, Miscellaneous
Expect scripts work well for performing automated tasks without the need to learn shell scripting or the need for user input (such as, username and password). Expect is available for download for a variety of operating system flavors from: Expec...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
Contact a Digi expert and get started today! CONTACT US