Home > Support > Knowledge Base

Knowledge Base

All
Configuration: 8 result(s) found
Installation: 9 result(s) found
Hardware: 6 result(s) found
Miscellaneous: 6 result(s) found
Troubleshooting: 3 result(s) found

 

There are 22 search results for ""
Installing a PC/X adapter in Windows NT
Category: Installation
Symptom: I can not find Windows NT drivers for my PC/X adapter. Cause: Digi does not provide Windows NT drivers for the PC/X adapters. Solutions: Digi provides installation information below for customers wishing to use the PC/X prod...
Where can I find drivers for my PC/X board?
Category: Installation
There are Digi drivers for the PC/X boards in OS/2 and Windows 3.1. These drivers can be found on the Digi Technical Support web site. For Linux, use the standard serial driver. For QNX and SCO OpenServer the driver is provided by the vendor....
PC/X and MC/X support in Windows 95/98/ME?
Category: Installation
Symptom: I cannot find a Windows 9x/ME driver for my PC/X or MC/X non-intelligent board. How do I get it to work? Cause: The PC/X or MC/X is not supported under the Windows 9x/ME operating systems, therefore there is no driver. Solutions...
Installing PC/X and ISA ClassicBoard Adapters in Linux
Category: Installation
Initial Configuration Determine the I/O Addresses: ClassicBoard:Run DOS configuration util (cfg) or use isapnp in linux. PC/4, PC/8:Configurable via DIP switches on the board itself. PC/16: I/O Addresse...
PC/X Adapter Dip Switch Configuration
Category: Configuration
PC/X Adapter Dip Switch Configuration PC/4 & PC/8 Non-Intelligent Asynchronous Serial Communication Boards Setting the I/O Port Addresses Breakdown of DIP Switch DS1 Status register is set ...
Installing a PC/X Adapter in SCO OpenServer
Category: Installation
Installing a PC/X Adapter in SCO OpenServer How to install PC/X non-intelligent board under SCO OpenServer: * Driver is built into SCO. * Only boards supported are PC/4 & PC/8 - PC/16 is not supported * No other COM port...
Installation Guide: PC/X and Classic ISA cards in Windows 2000/XP
Category: Installation
NOTE: This document is provided solely as a service to Digi customers.  Digi does not provide support for this product in this operating system.  This driver is provided by Microsoft, if you experience problems with the driver, please conta...
Installing PC/X and Classic ISA Adapters in Windows Xp
Category: Configuration, Installation
**This document is provided solely as a service to Digi customers.  Digi does not provide support for this product in this operating system.  This driver is provided by Microsoft, if you experience problems with the driver, please contact M...
How to Configure a Linux System Serial Port for Console Management Using Grub.
Category: Configuration
The linux box won''''''''t have console turned on by default, you will need to spawn a getty at ttyS0 (the first serial port). Here is an example of the /etc/inittab file entry: 0:12345:respawn:/sbin/agetty 9600 ttyS0 Configure /etc/grub.conf: ...
Pin-Outs for DB-78 Octopus Cables:For all PC/X, Classicboard, Xi, Xe, Xr and Xr920 4 and 8 port cards
Category: Hardware
Cable Pinouts 78 Pin Cable RS 422 db9 and db25 Pinouts 78 Pin DCE RS 232 db9 Cable Pinout 78 Pin DTE RS 232 db9 Cable Pinout 78 Pin DCE RS 232 db25 Cable Pinout 78 Pin DTE RS 232 db25 Cable Pinout
EIA-232 Information
Category: Hardware
DTE vs DCE This is one of the most misunderstood areas of RS-232. DTE stands for Data Terminal Equipment, and DCE stands for Data Circuit-terminating Equipment or Data Communications Equipment. The DTE is typicall...
Recommended Custom Cable Vendors
Category: Miscellaneous
The Whyte Haus 260-484-5666 the.whytehaus@verizon.net Contact: Barb Whyte   Predator Grizzly Cable (503)292-7151 x 1101 CSP, Inc. 763-475-8346 mrannals@csp.com ...
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
What is Digi International doing to comply with the RoHS requirements?
Category: Miscellaneous
Digi International is in the process of preparing to meet the RoHS requiements. For details, please visit this link:  http://www.digi.com/aboutus/environment.jsp  
How can I make a cable to attach a terminal with a DEC MMJ6 to a Digi RJ-45 connector?
Category: Hardware, Miscellaneous
Here is the pinout to attach a terminal or other DTE device to a Digi product which has RJ-45 connectors: DEC Digi MMJ6 8-wire RJ45 ------------------------------------ DSR 1 ------------------ 8 DTR R...
How do I configure my CUPS printers for hardware flow control instead of the default software flow control?
Category: Configuration, Troubleshooting
Change the printer configuration (/etc/cups/printers.conf) file to reflect hardware flow control. Here is an example: DeviceURI serial:/dev/ttyx##?baud=9600+size=8+parity=none+flow=hard
MISSING ALL COM PORTS IN WINDOWS 2000
Category: Troubleshooting
  Make sure that the system has at least one of it''''''''s native serial ports enabled in the system BIOS. Failure to do this will prevent the Microsoft Serial Driver from loading. The Digi makes use of it and will not be able to load without ...
Reference Guide: Cable specifications for building serial cables
Category: Hardware
Cable Reference Guides: EIA-232 General Information EIA-232 Flow Control Primer EIA-232 Cables: DTE vs. DCE EIA-232 Signal Information EIA-232 Cable Specifications EIA-232 Cable Capacitance vs. Length of Run EIA-232 Signal/Pin Convers...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
How do I configure getty in newer versions of Ubuntu?
Category: Configuration
Newer versions of Ubuntu no longer use the /etc/inittab file for configuing getty. A new method is now used called upstart. This requires a file be created in /etc/event.d with the name of the tty device. Here is a basic example of the contents of /...
How do I configure getty in newer versions of Fedora?
Category: Configuration
Newer versions of Fedora Linux no longer use the /etc/inittab file for configuing getty. A new method is now used called upstart. This requires a file be created in /etc/event.d with the name of the tty device. Here is a basic example of the content...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
Contact a Digi expert and get started today! CONTACT US