Knowledge Base

All
Configuration: 4 result(s) found
Installation: 6 result(s) found
Hardware: 8 result(s) found
Miscellaneous: 12 result(s) found
Troubleshooting: 4 result(s) found

 

There are 16 search results for ""
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
Department of Defense Form 1494 (DD 1494)
Category: Miscellaneous
When installing radio systems on a military base or other Department of Defense sites it is necessary to obtain equipment certification from the National Telecommunications and Information Administration (NTIA) by submitting DD form 1494, Application...
Maximizing range
Category: Installation, Hardware
This document introduces the basics of a wireless communications system and explains how to maximize range when commissioning a system. It explains how to install radios, antennas and cables in a way to maximize the reliability of communication. ...
Vibration and shock testing and performance
Category: Hardware, Installation, Miscellaneous
We have had several inquiries about how well the Digi radio modems perform in high vibration environments. Digi has not conducted any vibration analysis tests on our own products. However, our customers have done extensive testing lab and field testi...
Is RSSI the best indication of link quality?
Category: Miscellaneous
One thing to keep in mind is that the RSSI is only an indication of the RF energy detected at the antenna port. The power level reported could be artificially high because it may include energy from background noise and interference as well as the...
Antenna and cable impedance
Category: Hardware, Installation
Digi RF products are engineered to drive a 50 ohm load. All RF cables or antennas attached to the antenna connector should provide a 50 ohm match. Ensure that the cable being used is rated for the frequency of the module you are using, we recommen...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
Intrinsic safety certifications
Category: Hardware, Miscellaneous
What information do I need to obtain Intrinsic safety certifications? Digi radio modems have been integrated by a number customers into products that are used in hazardous environments. For electronic equipment to be used in environments with com...
Minimum seperation distance between antennas and nearby persons
Category: Installation, Hardware
Digi RF products are FCC approved for use in fixed base station and mobile applications. As long as the antenna is mounted at least 20cm (8in) from nearby persons, the application is considered a mobile application. If the antenna will be mounted clo...
Radio Emission Designation And Modulation Type For Digi RF Radios
Category: Miscellaneous
9XStream/9XCite Modulation Type: FSK Emission Designation: 260KF1D 24XStream Modulation Type: FSK Emission Designation: 400K0F1D 9XTend Modulation Type: FSK (@9600 baud), GFSK (@115200 baud) Emission Designation: 350KF1D (XT09) EmissionD...
Using Port Monitoring Software for Troubleshooting
Category: Miscellaneous, Troubleshooting
Some integrators who start with a working hard-wired application may find they are not successful when substituting the radios for the wired connection. The best troubleshooting approach is to isolate the problem. A good starting point is to ensure t...
RoHS Certificate of Compliance
Category: Miscellaneous
RF Products as of 1 June, 2013 The wireless devices identified in this certificate are in compliance with the European Union Directive 2011/65/EU on the restricted use of certain hazardous substances (RoHS Directive / RoHS II Directive). Based o...
The AT Command Set
Category: Configuration, Miscellaneous
The AT command set, also known as the Hayes command set, was originally developed for use with the Hayes modems in the 1980s. Many modern dialup modems are still based around this standard. The term AT command comes from the use of the ASCII characte...
Zigbee Layer Acks: How can I be sure that my zigbee end device got data from my Python application?
Category: Miscellaneous, Troubleshooting
This article explains how to configure a Python application''s socket connection so that it waits to hear back from the zigbee end device before proceeding. This is opposed to normal behavior, which is simply sending the data down to the zigbee layer...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
Recovery procedure for Digi RF products
Category: Configuration, Hardware, Troubleshooting
This article is an all-inclusive guide for recovering a Digi RF product that is in an unresponsive state. Please click on the type of radio you are experiencing problems with to go to the appropriate section: • General troubleshooting...
Your M2M Expert®for Businessfor Developers
Contact Us
Phone
Email
Chat
Feedback
Newsletter SignupYouTubeGoogle+FacebookCopyright © 1996-2014 Digi International Inc. All rights reserved. Legal