Home > Support > Knowledge Base

Knowledge Base

All
Configuration: 8 result(s) found
Installation: 6 result(s) found
Hardware: 3 result(s) found
Miscellaneous: 9 result(s) found
Troubleshooting: 7 result(s) found

 

There are 17 search results for ""
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
How to install and use Wireshark (Ethereal) for Ethernet Packet Sniffing
Category: Installation, Miscellaneous, Troubleshooting
Wireshark Installation and Usage This document was put together to assist in the installation and usage of an Ethernet packet sniffing utility called Wireshark. To install Wireshark you will need to go to http://www.wireshark.org/download.html ...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
Does Digi offer products capable of 9 bit character serial communication?
Category: Miscellaneous
Digi products currently only support 5, 6, 7 and 8 bit characters for serial data.
How do I configure getty in newer versions of Ubuntu?
Category: Configuration
Newer versions of Ubuntu no longer use the /etc/inittab file for configuing getty. A new method is now used called upstart. This requires a file be created in /etc/event.d with the name of the tty device. Here is a basic example of the contents of /...
How do I configure getty in newer versions of Fedora?
Category: Configuration
Newer versions of Fedora Linux no longer use the /etc/inittab file for configuing getty. A new method is now used called upstart. This requires a file be created in /etc/event.d with the name of the tty device. Here is a basic example of the content...
How I can enable the RTS Toggle feature in Linux RealPort?
Category: Configuration
Issue the following command from the root prompt: # ditty-rp rtstoggle ttyx## Where ttyx## represents that actual tty ID.
Getty respawning errors are seen when rebooting the Linux server
Category: Configuration, Troubleshooting
In some cases it may take some time for the ports to fully initialize on start up, depending on the network initialization/WAN speeds, etc... As a result, the inittab file is read prior to the ports being fully initialized. To add time for the ports...
Printer configuration with AIX RealPort
Category: Configuration
The AIX server: # smit printer Select the following menu items: Printer/Plotter Devices Add Printer/Plotter osp Other serial printer rs232 Select appropriate sa device Fill in the options to match the printer settings: PORT number ...
Bluescreen when installing RealPort on a system running AVG Anti-virus, pointing to the ''avgtdix.sys'' file as the cause of the problem.
Category: Miscellaneous, Troubleshooting
Solution: Disable AVG from the system until RealPort is installed. How to Resolve: Open up Device Manager and uninstall any failed installs from the "Multi-port serial adapters" section, by right-clicking the device and clicking "Uninstall". ...
What does OFC and IFC mean and how do I resolve it?
Category: Installation, Miscellaneous, Troubleshooting
OFC represents ouptut flow control. IFC represents input flow control. When either of these are shown high or solid it indicates that a buffer overflow has occured on either the attached device (OFC) or the Digi serial port (IFC). Cause: There is...
Why do products have an altitude limit?
Category: Hardware, Miscellaneous, Troubleshooting
1 Altitude affects the cooling ability of the device. At higher altitudes, the reduced air pressure reduces the rate at which heat from the device can be dissipated to the surrounding ambient. 2 Products temperature rating assumes use at sea leve...
Performing a loopback test on Digi Connect and ConnectPort units using connect
Category: Troubleshooting
Loopback Testing on Device or Terminal Servers Using Connect 1. A loopback plug is shipped with Digi products for serial port testings. Plug the loopback plug into the serial port to be tested.   2. From the Windows CMD or a Unix/...
Steps for Updating the Linux RealPort Driver
Category: Configuration, Installation
We recommend installing the latest driver release from: http://www.digi.com/support/productdetail?pid=2247&type=drivers Update instructions:   cp /etc/dgrp.backing.store /etc/orig.dgrp.backing.store Turn off all getty processes in /etc...
Is it Possible to Route Data From the Wired Ethernet Port (LAN) to the Wireless Network (LAN) with the ConnectPort TS W product?
Category: Miscellaneous
No, this is not possible.  You would need a Wireless Access Point to accomplish this. You are able to have both the Ethernet and Wi-Fi running at the same time, and access to the serial ports from both networks.  However, the ConnectPort...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
How to Install RealPort in Red Hat or CentOS 6
Category: Installation
First ensure the following package dependencies are installed on your system: make, rpm-build, bash, gcc, glibc-devel, kernel-devel, kernel-headers, ncurses-devel, perl, and tcsh. The kernel-devel and kernel-headers packages must match your run...
Contact a Digi expert and get started today! CONTACT US

Desktop Site