Knowledge Base

All
Configuration: 4 result(s) found
Installation: 6 result(s) found
Hardware: 5 result(s) found
Miscellaneous: 8 result(s) found
Troubleshooting: 8 result(s) found

 

There are 12 search results for ""
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
How to install and use Wireshark (Ethereal) for Ethernet Packet Sniffing
Category: Installation, Miscellaneous, Troubleshooting
Wireshark Installation and Usage This document was put together to assist in the installation and usage of an Ethernet packet sniffing utility called Wireshark. To install Wireshark you will need to go to http://www.wireshark.org/download.html ...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
Bluescreen when installing RealPort on a system running AVG Anti-virus, pointing to the ''avgtdix.sys'' file as the cause of the problem.
Category: Miscellaneous, Troubleshooting
Solution: Disable AVG from the system until RealPort is installed. How to Resolve: Open up Device Manager and uninstall any failed installs from the "Multi-port serial adapters" section, by right-clicking the device and clicking "Uninstall". ...
What does OFC and IFC mean and how do I resolve it?
Category: Installation, Miscellaneous, Troubleshooting
OFC represents ouptut flow control. IFC represents input flow control. When either of these are shown high or solid it indicates that a buffer overflow has occured on either the attached device (OFC) or the Digi serial port (IFC). Cause: There is...
Why do products have an altitude limit?
Category: Hardware, Miscellaneous, Troubleshooting
1 Altitude affects the cooling ability of the device. At higher altitudes, the reduced air pressure reduces the rate at which heat from the device can be dissipated to the surrounding ambient. 2 Products temperature rating assumes use at sea leve...
Performing a loopback test on Digi Connect and ConnectPort units using connect
Category: Troubleshooting
Loopback Testing on Device or Terminal Servers Using Connect 1. Plug the RJ-45 loopback plug into the serial port to be tested.   2. From the Windows CMD or a Unix/Linux "root" prompt, telnet to the IP address of the Digi d...
Restore Digi ConnectPort LTS to Factory Default Settings
Category: Troubleshooting, Hardware
To restore the Digi ConnectPort LTS unit to the factory default configuration settings, use a TFTP or BOOTP server. To use the Bios menu to flash new firmware, do the following: Connect the console port on the rear panel of the Digi ConnectPor...
Steps for Updating the Linux RealPort Driver
Category: Configuration, Installation
We recommend installing the latest driver release from: http://www.digi.com/support/productdetail?pid=2247&type=drivers Update instructions:   cp /etc/dgrp.backing.store /etc/orig.dgrp.backing.store Turn off all getty processes in /etc...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
How to Install RealPort in Red Hat or CentOS 6
Category: Installation
First ensure the following package dependencies are installed on your system: make, rpm-build, bash, gcc, glibc-devel, kernel-devel, kernel-headers, ncurses-devel, perl, and tcsh. The kernel-devel and kernel-headers packages must match your run...
Do Any Digi Products Support Modbus Cry Out?
Category: Troubleshooting, Hardware, Configuration, Miscellaneous
Some Modbus serial slave devices have the ability to send a "cry out" which is an unsolicited event alert. This is not standard Modbus, and thus our industrial automation engine doesn't support it. Although this won't work in an industrial automat...
Your M2M Expert®for Businessfor Developers
Contact Us
Phone
Email
Chat
Feedback
Newsletter SignupYouTubeGoogle+FacebookCopyright © 1996-2014 Digi International Inc. All rights reserved. Legal