Home > Support > Knowledge Base

Knowledge Base

All
Configuration: 22 result(s) found
Installation: 16 result(s) found
Hardware: 8 result(s) found
Miscellaneous: 17 result(s) found
Troubleshooting: 20 result(s) found

 

There are 28 search results for ""
What ports are used with the ADDP protocol?
Category: Configuration, Hardware, Installation, Troubleshooting
ADDP uses udp port 2362 and a mulicast ip address of 224.0.5.128. You will need to enable these on your firewall for the ADDP protocol to work for the device discovery utility.
How to recover a Digi Connect (Wi-)ME (9210), (Wi-)EM and (Wi-)SP JTAG'less C module
Category: Configuration, Miscellaneous, Troubleshooting
Introduction This document describes how to recover a Digi Connect ME (9210), EM, & SP JTAG'less C module (hereafter defined as a module) with a user defined image. These modules however need to be the ''C'' or Custom variant. They also need ...
Device Discovery Troubleshooting Tips
Category: Installation, Troubleshooting
INTRODUCTION This document contains a list of tips that will help people through the trouble of detecting most Digi Ethernet or Wi-Fi devices. Some examples are the Digi Connect ME, EM, SP, WiME, WiEM, WiSP -S modules running Plug n' Play firmware...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
creating partitions and updating U-Boot from U-Boot bootscript / autoscript does not work due to interactive inputs required
Category: Configuration, Miscellaneous, Troubleshooting
U-Boot autoscript feature is described in /usr/local/DigiEL-5.2/docs/Software/U-Boot_Reference_Manual.pdf Revision H in section 6. However when using this for production, it does not allow to run "flpart" or "update uboot" from this, as those command...
Why do products have an altitude limit?
Category: Hardware, Miscellaneous, Troubleshooting
1 Altitude affects the cooling ability of the device. At higher altitudes, the reduced air pressure reduces the rate at which heat from the device can be dissipated to the surrounding ambient. 2 Products temperature rating assumes use at sea leve...
Steps for Updating the Linux RealPort Driver
Category: Configuration, Installation
We recommend installing the latest driver release from: http://www.digi.com/support/productdetail?pid=2247&type=drivers Update instructions:   cp /etc/dgrp.backing.store /etc/orig.dgrp.backing.store Turn off all getty processes in /etc...
How do I write assembly code in .C file of a NET+OS application project ?
Category: Configuration, Hardware, Miscellaneous
Refer inclusion of assembly in gnu C code. Sample Code :- {please note that in the below code snippet, double qoutes are replaced with single quotes (') for search engine optimization} #include <stdio.h> #include <stdlib.h> ...
How to get rx_signal value of wln_status structure in dBm units on devices running NET+OS 6.3.
Category: Configuration, Installation, Miscellaneous, Troubleshooting
Wifi RSSI strength is populated in rx_signal (structure variable) of wln_status structure. In API Reference Manual, if description for rx_signal field is NOT specifying that it is dBm units, then you need to follow th...
How do I recompile Digi pre-compiled binaries with different options, with Digi Embedded Linux 5.7 toolchain. Example: wpa_supplicant
Category: Configuration, Installation, Miscellaneous, Troubleshooting
Mount the Digi Embedded Linux 5.7 Live DVD and copy the Digi toolchain patches to a local directory: example package: wpa_supplicant # cp -r /media/DigiEL_LiveDVD/toolchain/del_toolchain/packages/wpa_supplicant/ ~ # chmod -R u+rwX ~/wpa_supplica...
Installed NET+OS 7.5.2 and all updates but getting build errors like >> multiple definition of ***Mesh***
Category: Installation, Miscellaneous, Troubleshooting
While applying NET+OS 7.5.0 AWS and Email Updates The following message pops up before the AWS patch can be installed.   NET+OS 7.5.0 AWS and Email Updates Please note that Package Manager does not have the ability to remove files ...
How to get rid of NET+OS 7.5 different build errors on Windows 7 64-bit machine
Category: Configuration, Installation, Troubleshooting
DISCLAIMER :- Digi ESP is not officially supported on Windows 7 64-bit Host. The Solution explained here is only a workaround which may or may not work depending on your privileges on Host Machine. Make sure that you have applied all latest patch...
How do I get a user login prompt in Digi Embedded Linux bootup on Connect & ConnectCore devices ?
Category: Configuration, Miscellaneous
DEL with kernel 2.6.35.14 or above will support multiple users on target boards. ie: 5.7, 5.8, 5.9 etc. To get user login prompt in Linux boot follow the below :- Create a DigiEL-Kernel/Rootfs/U-boot Project in Digi ESP for DEL Edit work...
How to recompile Qt with Digi Embedded Linux 5.8
Category: Configuration, Installation, Miscellaneous, Troubleshooting
On a Linux PC where you have installed your Digi Embedded Linux ESP and toolchain, typically under /usr/local/DigiEL-*/ create a local working directory and change into it. E:g. # mkdir ~/DEL58toolchain # cd ~/DEL58toolchain Mount the Digi Emb...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
uboot tftp transfer is not working on office/work laptop, but works on desktop, why?
Category: Configuration, Hardware, Installation, Troubleshooting
Office laptops usually will have VPN installed. It appears that some VPN Clients will reconfigure MTU value to 1300 bytes, presumably as a requirement of the VPN tunnel or to minimize delays. This means that when using a TFTP server with the opti...
Device Cloud Migration Guide:  How do I migrate my gateway to a different Device Cloud server?
Category: Configuration, Hardware, Troubleshooting
Introduction Digi makes a number of different products capable of connecting to the Device Cloud , from hardware products to those which are purely software.  Unfortunately, not all of these devices have the...
Getting Device Cloud Connected:  Configuring Digi Connect and ConnectPort Gateways for Device Cloudconnection - Web User Interface (WebUI) method
Category: Configuration
Changing a Gateway's Device Cloud Remote Configuration settings from the Device Cloud: The easiest way to change the Device Cloud configuration of supported Gateway is from the Device Cloud UI Properties page of a Gateway which is already&nbs...
Booting Linux or Android, you observe a message like: Ganges-SDIO WLAN: probe of mmc0:fffd:1 failed with error 1 and you notice WiFi does not work.
Category: Configuration, Miscellaneous, Troubleshooting
During manufacturing test, Digi operations switches driver to RF evaluation mode. On some batches Digi missed to switch back to normal mode, which is causing the Linux WLAN drivers not to work. To fix the problem set U-Boot environment variable w...
How to install multiple releases of Digi Embedded Linux(DEL) together
Category: Configuration, Installation, Miscellaneous, Troubleshooting
Default DEL installation folder is /usr/local/DigiEL-x.y and should not be installed as root. Declarations: Digi Embedded Linux package comes with an Eclipse based IDE 'Digi ESP' .  Digi has tested Digi ESPs on - 5.2 on Kubuntu 8.10 ...
How to work with ADDP device discovery protocol and devices running embedded Linux like ConnectCore, ConnectCard, Digi Connect ME 9210
Category: Configuration, Installation, Miscellaneous, Troubleshooting
In order to be able to search for embedded Linux devices in your local network with the ADDP protocol using broadcasts/multicasts you need to add the "addpd" to your root file system. This can be done in Digi Embedded Linux ESP in a rootfs project j...
Loading Linux CAN drivers during runtime shows: [ ERROR ] fim-can: Couldn't request the GPIO14 fim-can: probe of fim-can.0 failed with error -22
Category: Configuration, Hardware, Miscellaneous, Troubleshooting
This could mean you have enabled drivers using GPIO14 e.g. UARTC or Ethernet activity LED. Disable this driver in your kernel. If message persists, your module does not support CAN. Not all Connect ME 9210 modules do support CAN. Mostly new versio...
Running QT application on DEL modules shows NO output in LCD display
Category: Configuration, Hardware, Troubleshooting
A Qt for Embedded Linux application requires a server application to be running, or to be the server application itself. Any Qt for Embedded Linux application can be the server application by constructing the QApplication object with the QApplication...
How to Install RealPort in Red Hat or CentOS 6
Category: Installation
First ensure the following package dependencies are installed on your system: make, rpm-build, bash, gcc, glibc-devel, kernel-devel, kernel-headers, ncurses-devel, perl, and tcsh. The kernel-devel and kernel-headers packages must match your run...
Digi Embedded Linux (DEL) graphical project or kernel configuration fails with: make -k xconfig HOSTCXX scripts/kconfig/qconf.o make: ***[xconfig] Error 2
Category: Configuration, Installation, Miscellaneous, Troubleshooting
Sometimes you see more details, e.g.: make -k xconfig   CHECK   qt sed < /usr/local/DigiEL-5.9/scripts/scripts/kconfig/lkc_proto.h > scripts/kconfig/lkc_defs.h 's/P(\([^,]*\),.*/#define \1 (\*\1_p)/'   HOSTCC&n...
Can't update U-Boot or Linux via Ethernet on my Digi Connect ME 9210
Category: Configuration, Installation, Troubleshooting
The factory programmed U-Boot on Digi Connect ME 9210 might not allow you to update firmware via Ethernet on your custom board. Either plug the module to a Digi development board to update firmware, or use the serial console as follows: Connect via ...
how to disable serial console in Linux to allow application to use serial port UART
Category: Configuration, Installation, Miscellaneous
Open Digi Embedded Linux 5.7 and create a project with kernel. Configure the kernel and disable (just search for it in config): CONFIG_SERIAL_CORE_CONSOLE CONFIG_SERIAL_NS921X_CONSOLE you may disable the serial port completely or enable any fea...
Forgot the root password for NET+OS firmware. Can't change wrong baud rate settings
Category: Troubleshooting
When your NET+OS firmware device does not boot anymore and you are trying the recovery method, you may manage to upload a firmware image.bin, however it might still not boot due to wired NVRAM settings like wrong baud rate. When trying to change the ...
Contact a Digi expert and get started today! CONTACT US

Desktop Site