Knowledge Base

All
Configuration: 9 result(s) found
Installation: 9 result(s) found
Hardware: 16 result(s) found
Miscellaneous: 16 result(s) found
Troubleshooting: 5 result(s) found

 

There are 25 search results for ""
Where can I locate Legacy drivers?
Category: Miscellaneous, Configuration, Hardware, Installation, Troubleshooting
Please visit the following page ftp://digiftp.digi.com/support_archive
How to mechanically secure RF module
Category: Hardware, Installation
The XStream, XCite, and XBee RF modules do not have mounting holes through the PC board so we have suggested several other methods for securing the module: Position the module in the housing so that the packaging provides a mechanical barrie...
Maximizing range
Category: Installation, Hardware
This document introduces the basics of a wireless communications system and explains how to maximize range when commissioning a system. It explains how to install radios, antennas and cables in a way to maximize the reliability of communication. ...
Vibration and shock testing and performance
Category: Hardware, Installation, Miscellaneous
We have had several inquiries about how well the Digi radio modems perform in high vibration environments. Digi has not conducted any vibration analysis tests on our own products. However, our customers have done extensive testing lab and field testi...
Is RSSI the best indication of link quality?
Category: Miscellaneous
One thing to keep in mind is that the RSSI is only an indication of the RF energy detected at the antenna port. The power level reported could be artificially high because it may include energy from background noise and interference as well as the...
Antenna and cable impedance
Category: Hardware, Installation
Digi RF products are engineered to drive a 50 ohm load. All RF cables or antennas attached to the antenna connector should provide a 50 ohm match. Ensure that the cable being used is rated for the frequency of the module you are using, we recommen...
Use of content from Digi manuals
Category: Miscellaneous
Content from Digi manuals may be used by our OEM customers in their own documentation subject to the following conditions: Clearly state: "Parts of this manual are used by permission of Digi, Inc." Submit a copy of the...
Intrinsic safety certifications
Category: Hardware, Miscellaneous
What information do I need to obtain Intrinsic safety certifications? Digi radio modems have been integrated by a number customers into products that are used in hazardous environments. For electronic equipment to be used in environments with com...
Minimum seperation distance between antennas and nearby persons
Category: Installation, Hardware
Digi RF products are FCC approved for use in fixed base station and mobile applications. As long as the antenna is mounted at least 20cm (8in) from nearby persons, the application is considered a mobile application. If the antenna will be mounted clo...
Should I use a 1/4 wave or 1/2 wave antenna?
Category: Hardware, Installation
What is the difference between a ½-wave and a ¼-wave antenna? Antenna Type ½-wave ¼-wave Alternate name Dipole ...
Radio Emission Designation And Modulation Type For Digi RF Radios
Category: Miscellaneous
9XStream/9XCite Modulation Type: FSK Emission Designation: 260KF1D 24XStream Modulation Type: FSK Emission Designation: 400K0F1D 9XTend Modulation Type: FSK (@9600 baud), GFSK (@115200 baud) Emission Designation: 350KF1D (XT09) EmissionD...
Which RF connector is better to use: MMCX, RPSMA, or U.FL?
Category: Hardware
Digi radios come in a variety of antenna options. The options that allow you to connect an external antenna are RPSMA, MMCX, and U.FL. RPSMA is the more traditional antenna connector, however if the radio is going to be inside of an enclosure, the...
Interfacing Digi OEM RF Modules to Microcontrollers
Category: Hardware
Digi radios are compatible with microcontrollers from a variety of vendors. For this reason, Digi does not make recommendations for choosing a specific microcontroller to interface with our radios. However, we can offer a few feature suggestions to c...
Using Port Monitoring Software for Troubleshooting
Category: Miscellaneous, Troubleshooting
Some integrators who start with a working hard-wired application may find they are not successful when substituting the radios for the wired connection. The best troubleshooting approach is to isolate the problem. A good starting point is to ensure t...
Wireless CAN (Controller Area Network)
Category: Miscellaneous
The CAN (Controller Area Network) serial protocol was originally designed to be used for communication between sensors and computers in automotive applications. Since its inception it has grown to be used in a number of different commercial and indus...
XBee ZigBee Route Discovery and Network Address Discovery
Category: Configuration
In ZigBee there are two important forms of discovery that allow one node to locate and send packets to another node. These two methods are called Route Discovery and Network Address Discovery. Route Discovery: In order for an XBee module to sen...
RoHS Certificate of Compliance
Category: Miscellaneous
RF Products as of 1 June, 2013 The wireless devices identified in this certificate are in compliance with the European Union Directive 2011/65/EU on the restricted use of certain hazardous substances (RoHS Directive / RoHS II Directive). Based o...
The AT Command Set
Category: Configuration, Miscellaneous
The AT command set, also known as the Hayes command set, was originally developed for use with the Hayes modems in the 1980s. Many modern dialup modems are still based around this standard. The term AT command comes from the use of the ASCII characte...
How to find out the date code and manufacturing location information of Digi Products.
Category: Configuration, Hardware, Installation, Miscellaneous
Depending on the location the units are built effects the orientation, linked below is the date code from USA or Thailand.  The date code is 4 digits, 2 digit year and 2 digit week (YYWW) so in these examples the 26th week of 2012. Thailand M...
Maximum payload size for Digi RF radios
Category: Configuration, Miscellaneous, Troubleshooting
When the radio is being used in a transparent (AT) mode, packet size is irrelevant because the data will be fragmented as needed. However, when using API frames, it is important not to exceed the allowable payload size.  Maximum payload size ...
An Introduction to SPI on XBee
Category: Miscellaneous, Hardware
  Download this article in a printable format    Introduction Purpose and Scope The purpose of this document is to specify how SPI is implemented on the XBee product line. It can be used by technical publications to create product...
Recovery procedure for Digi RF products
Category: Configuration, Hardware, Troubleshooting
This article is an all-inclusive guide for recovering a Digi RF product that is in an unresponsive state. Please click on the type of radio you are experiencing problems with to go to the appropriate section: • General troubleshooting...
Optimizing USB to Serial Port Settings 
Category: Configuration, Hardware, Installation, Miscellaneous, Troubleshooting
Digi interface boards and USB adapters use an FTDI Chip for the USB to serial conversion. The default configuration for FTDI's drivers are optimized for high speed serial devices. Digi RF radios operate at lower baud rates than are optimal for these ...
Understanding white label on XBee module
Category: Hardware, Configuration, Miscellaneous
  Location of label items will vary by product, and may change over time.
Digital and Analog Sampling Using XBee Radios
Category: Configuration, Hardware, Miscellaneous
  XBee radios have multiple I/O lines that can be used to gather Digital or Analog data, and then transmit that data to another XBee for interpretation. Because sample data is always provided in an API format, it can be very intimidating and...
Your M2M Expert®for Businessfor Developers
Contact Us
Phone
Email
Chat
Feedback
Newsletter SignupYouTubeGoogle+FacebookCopyright © 1996-2014 Digi International Inc. All rights reserved. Legal