Home > Support > Knowledge Base

Knowledge Base

Configuration: 9 result(s) found
Installation: 2 result(s) found
Hardware: 2 result(s) found
Miscellaneous: 11 result(s) found
Troubleshooting: 6 result(s) found


There are 17 search results for ""
What is the programming code that I use for Sprint Provisioning?
Category: Configuration, Installation, Troubleshooting
This somewhat depends on the CDMA module installed in the Digi device. Normally the programming code (or MSL) to use is six zeros (000000). For re-provisioning on devices with Gobi modules you may need the 6-digit MSL provided by Sprint. Te...
How to Configure Port Forwarding with Digi TransPort Routers
Category: Configuration
1) Log into the Web User Interface (WebUI), and navigate to Configuration – Network > Interfaces > Mobile. 2) Expand the Mobile Settings section, and change the Enable NAT on this interface to the IP address and Port option, as shown i...
Capturing a DSL Trace with Digi TransPort 
Category: Troubleshooting, Miscellaneous
Login to the Web Interface and navigate to Management> Analyser > Settings. Change the Maximum packet capture size to 1500 bytes. Change the Log size to 180 Kbytes. Check the box under DSL PVC Sources for PVC 0. Check the bo...
How to Clear CDMA Provisioning on Transports with Gobi
Category: Miscellaneous, Configuration
If you ever need to reset or change an account, the provisioning in the modem might need to be cleared. For example, if the cellular provider changes an account from Vision or Datalink to Command Center, the current provisioning in the modem has to b...
Digi TransPort FTP Port Forwarding
Category: Configuration
The following instructions describe how to configure the Digi TransPort’s VPN settings:    1) Log into the Web User Interface (WebUI), and navigate to Configuration – Network > Interfaces > Mobile.    2)...
What is the pinout for connecting the RJ45 port from a Digi TransPort to a Cisco or Juniper RJ45 console port?
Category: None
Cable pinout for connecting RJ45 Digi TransPort RS232 port to a Cisco or Juniper RJ45 RS232 serial port: Digi RJ45       Cisco/Juniper RJ45 ========     ============== RTS 1        ...
How to obtain a serial trace from a Digi TransPort router.
Category: Troubleshooting
The following steps outline how to obtain a trace from a Digi TransPort serial port: From the web interface of the Digi TransPort unit select:  Management-Analyser> Settings   -Enable Analyser  Use the check box to enab...
How to force the Digi TransPort to synchronize with the NTP/SNTP time servers
Category: Miscellaneous
The following command can be used to synchronize the time with pre-defined NTP/SNTP servers immediately.  This should be run from the router CLI prompt with administrative privileges.  sntp 0 now
What is the maximum USB storage recognized by Digi TransPort routers?
Category: Miscellaneous, Hardware
Digi TransPort products support USB devices formatted with FAT 16 and FAT 32.  If using FAT 32, 32GB is the largest partition recognized.
How to obtain DEBUG output on TransPort routers through an SSH client
Category: Troubleshooting
Debug output is usually obtained through the serial port (ASY0) or via telnet on the router (not SSH) The options are: "DEBUG 0"   ->   ASY0 "DEBUG 1"   ->   ASY1 "DEBUG T" ...
How To Extract the .ALL Digi TransPort File Using FlashWriter
Category: Miscellaneous, Configuration
A Digi TransPort .ALL file is a copy of the Digi TransPort’s full image including all configuration files, firmware files,and any files on the Digi TransPort flash filesystem. These files can be used to re-image a Digi TransPort. See http://www...
How To Configure the Digi TransPort Firewall to Allow Alternate SSH and Other Management Ports for External Access
Category: Miscellaneous, Configuration
With the standard rule in place, which allows SSH, you may see several external connection attempts in the Event log similar to the following:     15:58:28, 15 May 2014,GP socket connected: -> ###.###.###.###:5286 Fo...
Digi TransPort Primary and Secondary Antenna Recommendations for 3G and 4G
Category: Hardware, Miscellaneous
Digi TransPort 3G routers (with the exception of the WR11 model) use the Primary antenna on send and receive frequencies; while the Secondary (or AUX) antenna is receive only. So, while we strongly recommend using both antennas, if only one antenna i...
How to set an event in eventlog to see the signal strength of the mobile interface in TransPort?
Category: Configuration, Troubleshooting, Miscellaneous
To set an event in the event log for the signal strength of the mobile interface (when inserted with SIM card) navigate as shown below Configuration--> Network--> Interface--> Mobile--> Advanced Under " create a signal streng...
How to use a Digi TransPort as an SSH Client from the Command Line
Category: Configuration, Miscellaneous
The Digi TransPort routers firmware embed an SSH client which allows you to establish an SSH connection to another device from the command line of the router. The command implemented to use the SSH client is : sshc When logged in on the Digi Tr...
HOW TO: Upload and Run Python Scripts on Digi TransPort Routers
Category: Configuration, Miscellaneous
Upload and Run a Python Script on TransPort routers   1) Upload the script on the TransPort via WEB GUI In the WEB GUI, browse to Administration-File management > File editor, click in the Filename field (where there is "--edit...
Digi International Security Notice Vulnerability "GHOST"
Category: Installation, Miscellaneous, Troubleshooting
Digi International Security Notice CVE-2015-0235 March 6th, 2015 Overview A critical security vulnerability, reported as CVE-2015-0235,nicknamed “GHOST,” was discovered by Qualys. The vulnerability affects the GetHostbyNa...
Contact a Digi expert and get started today! CONTACT US

Desktop Site