The U-Boot environment is a block of memory in persistent storage. It is used to store variables in the form name=value.

## Where is the U-Boot environment?

The ConnectCore 6UL reads the U-Boot environment (including the MAC addresses) from a partition called environment in the NAND flash. If it does not find a valid environment on the NAND, U-Boot uses a hard-coded default environment:

• The environment is located at the offset determined by constant CONFIG_ENV_OFFSET in U-Boot source code at include/configs/ccimx6ulsbc.h and include/configs/ccimx6ulstarter.h.

• The size of the environment is determined by constant CONFIG_ENV_SIZE at the same header file.

• There is a back-up copy of the environment in the same NAND partition (where the original copy is) at the offset determined by constant CONFIG_ENV_OFFSET_REDUND in the same header file.

## Access U-Boot environment from Linux

You can access the U-Boot environment from a Linux application. In the U-Boot source tree, you can find the environment tools in the directory tools/env, which you can build with the following command:

``$make env`` Digi Embedded Yocto also compiles this tool by default and installs it on your target’s root file system as two executable files: • fw_printenv: to print the value of variables. • fw_setenv: to set the value of variables. The tools work with the configuration file /etc/fw_env.config, which must contain one or two entries in the form: Device name, offset, size. The first entry must point to the U-Boot environment location. The second (if present) must point to its redundant copy, for example: /etc/fw_env.config ``````# Configuration file for fw_(printenv/setenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Device name Offset Size /dev/mtd1 0x0 0x20000 /dev/mtd1 0x20000 0x20000`````` ## Append boot arguments to the kernel command line You can use the extra_bootargs variables to append commands to the default kernel command line. ## Important U-Boot environment variables on the ConnectCore 6UL The following U-Boot environment variables are worth mentioning: ### MAC addresses Variable Description Flags$ethaddr

MAC address of the first wired Ethernet interface

change-default

$eth1addr MAC address of the second wired Ethernet interface if there is one change-default$wlanaddr

MAC address of the Wi-Fi interface

change-default

$btaddr MAC address of the Bluetooth interface change-default  About flags Variables with write-once flag are protected and will not be overwritten by setenv or env default commands (unless manually forced with -f option). Variables with change-default flag can only be written once using setenv command (unless manually forced with -f option). Digi programs the MAC addresses of the ConnectCore 6UL during manufacturing and saves them in the U-Boot environment on the NAND. You can find the Digi-assigned MAC address on the ConnectCore 6UL module label. See Determine Digi MAC addresses for more information. ### Wireless virtual MAC addresses The wireless interface on the ConnectCore 6UL module allows you to define up to three optional virtual interfaces so that the platform can run concurrently as station, p2p, and SoftAP. Digi neither reserves nor programs unique MAC addresses for these virtual interfaces. A user who wishes to assign unique MAC addresses to such virtual interfaces can use the following U-Boot environment variables: Variable Description Flags$wlan1addr

MAC address of virtual wireless interface 1

change-default

$wlan2addr MAC address of virtual wireless interface 2 change-default$wlan3addr

MAC address of virtual wireless interface 3

change-default

### Module variant

Variable Description Flags

$module_variant Variant ID code for the System-On-Chip write-once During start-up, U-Boot automatically sets this variable to the ConnectCore 6UL System-On-Chip variant ID number (a hexadecimal code programmed in the SOM one-time programmable bits). ### Carrier board version and ID Variable Description Flags$board_version

Version number of the carrier board

write-once

\$board_id

ID number of the carrier board

write-once

During start-up, U-Boot automatically sets these variables to the carrier board’s version and ID numbers (decimal numbers programmed in the SOM one-time programmable bits). See Carrier board version and ID.

## Determine Digi MAC addresses

### Sequential MAC address scheme

Digi assigns MAC addresses according to a sequential scheme. The order of assignment depends on the available interfaces, but the scheme always respects the order Ethernet 1, Ethernet 2, Wi-Fi, Bluetooth and skips non-available interfaces.

### Determine MAC addresses

You can determine the MAC addresses for your device either by reading the Ethernet MAC off the label and using the scheme to calculate subsequent addresses, or by reading them from your device. To read the stock environment variables from the device using the `printenv` command executed at the U-Boot prompt:

To get First Ethernet MAC address:

``=> printenv ethaddr``

If your SOM has a second Ethernet MAC address:

``=> printenv eth1addr``

To get Wi-Fi MAC address:

``=> printenv wlanaddr``

To get Bluetooth MAC address:

``=> printenv btaddr``