Home/Support/Support Forum/How to interface Xbee with FPGA using SPI?
New and improved user forum site coming soon

How to interface Xbee with FPGA using SPI?

0 votes
I am trying to connect an Xbee S6 to a FPGA using SPI. I found some code online to read in the MISO and convert to an 8bit output register. I have it working in the simulation but I cannot get the correct output when I try to implement it. I connected dout from the Xbee to ground to initiate SPI mode, but i'm not sure how to confirm this. I have my clock set to 20 Mhz and the clock divider sets the SPI clock to under 5Mhz. Also, if I am just using one slave, can my select (ss) be held to zero?

I have a remote PC with HyperTerminal to send keyboard characters to the FPGA. I initially want to relay these hex keyboard codes to the LED's on the FPGA and later use these codes as input for motor control. The keyboard will be used as input for all of the motors used on a rover.

Here is the code I've been working on. I appreciate any assistance.

*I added MOSI section in the code and set tdat to FF
**LED outputs for rdata just switch between FF to 00 depending on the keyboard key pressed.
Code:
module SPI_test( input clk, input attn, input miso, input [7:0] tdat, output reg ss, output reg sck, output reg mosi, output reg [7:0] rdata, output ledtest, output reg ledtest2 ); assign ledtest = ~attn; //assign ledtest2 = ~ss; parameter idle = 2'b00; parameter send = 2'b10; parameter finish = 2'b11; reg [1:0] cur; reg [1:0] nxt; reg [7:0] rreg, treg; reg [3:0] nbit; reg [4:0] mid; reg [4:0] cnt; reg shift; reg clr; reg [1:0] cdiv = 2'b00; //FSM i/o always @ (attn or cur or nbit) begin nxt <= cur; clr <= 0; shift <= 0; //ss <= 0; case (cur) idle: begin if (attn==0) begin case (cdiv) 2'b00: mid <= 2; 2'b01: mid <= 4; 2'b10: mid <= 8; 2'b11: mid <= 16; endcase shift <= 1; nxt <= send; end end //idle send: begin ss <= 0; if (nbit != 9) shift <= 1; else begin rdata <= rreg; nxt <= finish; end end //send finish: begin shift <= 0; ss <= 1; clr <= 1; nxt <= idle; end default: nxt <= finish; endcase end //always //state transitions always @ (negedge clk) begin cur <= nxt; end //Setup clk for read miso always @ (negedge clk or posedge clr) begin if (clr == 1) begin cnt <= 0; sck <= 1; end else begin if (shift == 1) begin cnt <= cnt + 1; if (cnt == mid) begin sck <= ~sck; cnt <= 0; end //mid end //shift end //else end //always //read miso always @ (posedge sck or posedge clr) begin if (clr == 1) begin nbit <= 0; rreg <= 8'hFF; end else begin rreg <= {rreg[6:0],miso}; nbit <= nbit + 1; end end //always always@(posedge sck or posedge clr) begin if(clr==1) begin treg <= 8'hFF; mosi <= 1; end else begin if(nbit==0) begin //load data into TREG treg <= tdat; mosi <= treg[7]; end //nbit_if else begin treg <= {treg[6:0],1'b1}; mosi <= treg[7]; end //else end //rst end //always endmodule
asked Mar 26, 2015 in XBee Programmable Development by mtourtelot New to the Community (0 points)
edited Mar 26, 2015 by mtourtelot

Please log in or register to answer this question.

1 Answer

0 votes
No you do need all of the lines. You also need to trasnfer FF's in order to receve data. No you als oneed to have your Slave select set so that your device is the Master.
answered Mar 26, 2015 by mvut Veteran of the Digi Community (15,515 points)
Ok, so to enable the SPI ports, do I just send +++D0<enter> D1<enter> D2..ect for each of the pins?
May I suggest reading over Enabling SPI port section within the manual? It walks you through the process.
Yes, I have read that. I am asking for help understanding it
If you use the Modem configuration tab of XCTU, you would set
DIO7/nCTS    0
DIO6/nRTS    0
P3  0
P4  0
P2 1
P5  1
P6  1
P7 1
P8 1
P9  1
D1  1
D2 1
D3 1
D4  1

At the end of all of this you would use the Write function or the pencil on each command.
Ok, I got that, except I didnt see P5-P9. The LED's only switch between  FF, 01011100 (5C), and 01010100 (54) on random keys. It doesnt seem to be picking out the hex codes for the keys
...