Home/Support/Support Forum/Installing Android failed (Connect core CC-SB-WMX-L76C-1)
Welcome to Digi Forum, where you can ask questions and receive answers from other members of the community.

Installing Android failed (Connect core CC-SB-WMX-L76C-1)

0 votes
Hi,

I am trying to install Android 5.1 [https://www.digi.com/resources/documentation/digidocs/90001945-13/Default.htm#task/android/t_load_android_firmware.htm%3FTocPath%3DDigi%2520Embedded%2520for%2520Android%7CGet%2520started%7C_____3] to my CC-SB-WMX-L76C-1 device but it fails during installation process with error:

switch to partitions #0, OK
mmc0(part 0) is current device
Writing GPT: success!
>> Installing Android kernel and device tree files
Error: partition 'boot' not found
[ERROR] Failed to update android partition!

Does anybody have an idea how to overcome this issue?

Thanks in advance


Whole console installation log:
## Executing script at 12000000

############################################################

# Android firmware install from micro SD #

############################################################
This process will erase your eMMC and will install a new
U-Boot and Android firmware images on the eMMC.
Press CTRL+C now if you wish to abort or wait 10 seconds
to continue.
>> Installing U-Boot boot loader (target will reset)
reading u-boot-ccimx6dlsbc512MB.imx
363520 bytes read in 35 ms (9.9 MiB/s)
switch to partitions #1, OK
mmc0(part 1) is current device
MMC write: dev # 0, block # 2, count 710 ... 710 blocks written: OK
Reading back firmware...
MMC read: dev # 0, block # 2, count 710 ... 710 blocks read: OK
Verifying firmware...
Total of 90880 word(s) were the same
Update was successful
switch to partitions #0, OK
mmc0(part 0) is current device
Saving Environment to MMC...
Writing to redundant MMC(0)... done
resetting ...
U-Boot dub-2015.04-r2.3-dirty (Feb 15 2016 - 21:41:13)
CPU: Freescale i.MX6DL rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 46C
Reset cause: WDOG
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0 (eMMC), FSL_SDHC: 1
In: serial
Out: serial
Err: serial
ConnectCore 6 SOM variant 0x13: Industrial DualLite-core 800MHz, 4GB eMMC, 512MB DDR3, -40/+85C, Wireless, Bluetooth
Board: ConnectCore 6 SBC, version 3, ID 131
Boot device: MMC4
PMIC: DA9063, Device: 0x61, Variant: 0x60, Customer: 0x00, Config: 0x56
Net: FEC [PRIME]
Normal Boot
Hit any key to stop autoboot: 0
## Resetting to default environment
oldval: 00:40:9D:96:4F:D9 defval: 00:04:f3:ff:ff:fa
## Error: Can't overwrite "ethaddr"
himport_r: can't insert "ethaddr=00:04:f3:ff:ff:fa" into hash table
oldval: 00:40:9D:96:4F:DA defval: 00:04:f3:ff:ff:fb
## Error: Can't overwrite "wlanaddr"
himport_r: can't insert "wlanaddr=00:04:f3:ff:ff:fb" into hash table
oldval: 00:40:9D:96:4F:DB defval: 00:04:f3:ff:ff:fc
## Error: Can't overwrite "btaddr"
himport_r: can't insert "btaddr=00:04:f3:ff:ff:fc" into hash table
Saving Environment to MMC...
Writing to MMC(0)... done
>> Creating Android partition table on the eMMC
switch to partitions #0, OK
mmc0(part 0) is current device
Writing GPT: success!
>> Installing Android kernel and device tree files
Error: partition 'boot' not found
[ERROR] Failed to update android partition!


Aborted.
asked Nov 30, 2017 in Android by ondra3 New to the Community (0 points)

Please log in or register to answer this question.

1 Answer

0 votes
can you print your partition table and provide output here?
answered Nov 30, 2017 by LeonidM Veteran of the Digi Community (3,654 points)
...