Home/Support/Support Forum/Replace RCM3200 on a BL2600 board
Welcome to Digi Forum, where you can ask questions and receive answers from other members of the community.

Replace RCM3200 on a BL2600 board

0 votes
I have a BL2600 SBC with a bad RCM3200 core module. I ordered a stand alone RCM3200. Does anyone know what steps I need to take in order to use the new RCM3200 on the BL2600? I've tried writing a new ID block using the write_idblock_920_962.c file and followed the instructions, but it doesn't seem to be working. I am getting an out of data space error. Also, I don't know what size to make the user block. Hoping someone has done this before.
asked May 19 in Rabbit by mutantworm New to the Community (9 points)

Please log in or register to answer this question.

2 Answers

+1 vote
 
Best answer
I finally figured it out. I had to increase the DATAORG value in the bios file to 0x3000. Everything compiled successfully and I was able to change the ID of the RCM3200 to work with the BL2600 I/O board. Thanks to everyone who replied in this thread.
answered Aug 9 by mutantworm New to the Community (9 points)
selected Aug 9 by TomCollins
Instead of modifying the BIOS, you can just add a macro (DATAORG=0x3000) to the Defines tab of the Project Options window (via the Options menu).  I'm surprised the default values didn't work correctly.  Is it possible you already had an alternate value set in your Project Options?
commented Sep 9 by TomCollins Veteran of the Digi Community (2,184 points)
0 votes
Are you selecting the BL2600? Your board should be the following #define below if you are replacing it with an RCM3200. I'm not sure of your part# so I am assuming this is what you have.

//#define MYBOARD BL2600A // 44MHz RCM3200, 512K flash, 256K+512K SRAM, ethernet
answered May 19 by Campbell Veteran of the Digi Community (835 points)
Yes, I uncommented the BL2600A (that is indeed the board I am working with) in the writeidblock code file. I've tried several compiler configurations in DC 9.62 but I keep getting an error for not enough data space when I try to compile to the board. I also followed steps 13 through 16 in the comment sections of the writeidblock code file. The part number for the RCM3200 I am trying to use is 20-101-0520 if that helps.
commented May 19 by mutantworm New to the Community (9 points)
You may need a development board to change the RCM3200 to BL2600.  Digi no longer sells dev boards for RCM3000 products.
commented May 19 by Campbell Veteran of the Digi Community (835 points)
Can you "Compile to .bin" from Dynamic C?  Do you have any macros configured in the project settings?  What happened to the original RCM3200 in the BL2600?  You may be able to program the RCM3200 disconnected from the BL2600 if you have a good power supply that you can connect to the Vcc and GND pins of the RCM3200.
commented May 19 by TomCollins Veteran of the Digi Community (2,184 points)
It does not let me compile to bin file and I have no macros configured. All I get is "line    1 : ERROR DKCOMMON.LIB   : Out of constant data space."
commented May 27 by mutantworm New to the Community (9 points)
Can you even compile a simple sample program?  If not, it sounds like your Dynamic C installation has been modified.  Maybe you should start with a fresh install of Dynamic C 9.62A and see if that resolves anything.
commented May 28 by TomCollins Veteran of the Digi Community (2,184 points)
Sorry for the very late response. Yes, I can compile other programs.
commented Aug 9 by mutantworm New to the Community (9 points)
...