Hot questions - Digi Forum

0 votes

0 answers

SoftwareSerial with xbee is not working

asked 23 hours ago in ZNet 2.5 by javier_stickman New to the Community (0 points)

0 votes

0 answers

Sending gps commands through xbee

asked 1 day ago in XBee3 802.15.4 by daveb123 New to the Community (0 points)

0 votes

1 answer

Cellular Network Time via ATDT

asked 2 days ago in XBee3 Cellular by ehughes New to the Community (3 points)

0 votes

0 answers

XBee S2D ZigBee how many nodes?

asked 1 day ago in RF Solutions and XBee by MariusS New to the Community (0 points)

0 votes

1 answer

The latest run of XB3M1's won't associate with my cellular network.

asked 2 days ago in XBee Cellular by Washoegary New to the Community (2 points)

0 votes

1 answer

Setting IO Pin Doesn't work - solved

asked 2 days ago in RF Solutions and XBee by dazz New to the Community (12 points)

0 votes

0 answers

Do you have a device that supports Band14 cellular? If not, any plans to support?

asked 2 days ago in Digi Connect Cellular by jhaning New to the Community (0 points)

0 votes

0 answers

Am i stuck with one xbee on the control computer for every xbee remote? Which unit is recommend for such a use case?

asked 2 days ago in RF Solutions and XBee by jwoodyu New to the Community (0 points)

0 votes

0 answers

XCTU Cannot Find Firmware for ZigBee XStick 2

asked 2 days ago in IEEE 802.15.4 by miak New to the Community (0 points)

0 votes

0 answers

How to make all Xbee wake up/sleep when coordinator turns on/off automatically?

asked 2 days ago in Python by tchouzin New to the Community (0 points)

0 votes

0 answers

We have A Digi TransPort44WR, can I install a Data limit with message through email

asked 2 days ago in Digi Connect Cellular by elec_on_TL New to the Community (0 points)

0 votes

0 answers

Xbee s1 baud rate 115200 problem

asked 2 days ago in XBee Programmable Development by khalm New to the Community (0 points)

0 votes

1 answer

Manual or circuit diagram for SX 868 Dev Kit board?

asked 5 days ago in XBee3 by dazz New to the Community (12 points)

0 votes

1 answer

Initial time delay of data reaching the server

asked 6 days ago in Digi Connect Cellular by prasath New to the Community (0 points)

0 votes

1 answer

How to triangulate XBee3 Nb-IoT module using cellular network ?

asked Jul 10 in XBee3 Cellular by rajib New to the Community (1 point)

0 votes

1 answer

AnywhereUSB Connection lost after network interruption

asked Jul 9 in Realport by CupPrint New to the Community (1 point)

0 votes

1 answer

Can't figure out how to reset Digi Transport WR21

asked Jul 9 in Digi TransPort Cellular by LinuxMan756 New to the Community (0 points)

0 votes

1 answer

[xbee 3g global] how check voice calls in micropython/transparent mode?

asked Jul 9 in XBee Cellular by telejuan New to the Community (2 points)

0 votes

0 answers

How to ignore a break signal from my DTE to WR21 running the Python Serial to Device Cloud sample?

asked Jul 11 in Digi TransPort Cellular by testdigimonitor New to the Community (0 points)

0 votes

0 answers

Is there any possible way to suppress the " ... released a r/w session" messages in a serial connection?

asked Jul 11 in Console Servers by davidb89 New to the Community (0 points)