Recent questions tagged transmission

0 votes

1 answer

Connecting Xbee S2C to ESP8266-01 module.

asked Sep 15 in IEEE 802.11 (Wi-Fi) by LA New to the Community (0 points)

0 votes

1 answer

direct broadcast vs DIGIMESH

asked Dec 2, 2019 in DigiMesh Proprietary Mesh Networking by fd85 New to the Community (0 points)

0 votes

2 answers

can i increase range of my xbee s2c module by connecting to external antenna of higher dbi ?

asked Jan 25, 2018 in IEEE 802.15.4 by surajkumar New to the Community (0 points)

0 votes

1 answer

Transmit only works below a certain IR (Sample Rate)

asked Nov 1, 2017 in IEEE 802.15.4 by jweston New to the Community (0 points)

0 votes

1 answer

Reliable Transmission and 1 hop Broadcasting

asked Sep 1, 2017 in DigiMesh Proprietary Mesh Networking by YangShi New to the Community (0 points)

0 votes

1 answer

How to physically connect xbee wifi s6b to arduino to transfer data to xbee?

asked Aug 1, 2016 in Other/Legacy by alexes New to the Community (0 points)

0 votes

1 answer

How to get better range on my 2 x XBEE 900HP S3B peer-to-peer communication?

asked May 6, 2016 in RF Solutions and XBee by alejoast New to the Community (0 points)

0 votes

2 answers

XB24 pro series 1: Losing signal on LED costumes

asked Jan 14, 2016 in IEEE 802.15.4 by midascott New to the Community (0 points)

0 votes

1 answer

how to test antena range in mesh networking by using xctu software?

asked Dec 31, 2015 in ZigBee PRO Featureset (and legacy ZNet 2.5) by amar pulli New to the Community (0 points)

0 votes

1 answer

how to data transmissions from coordinator to end device through router?these are connected in the same network.

asked Dec 30, 2015 in ZigBee PRO Featureset (and legacy ZNet 2.5) by amar pulli New to the Community (0 points)

0 votes

1 answer

How can we transmit an array of data from one xbee S1 to another xbee module in AT mode?

asked Apr 5, 2015 in RF Solutions and XBee by ritalin046 New to the Community (0 points)

0 votes

1 answer

Problems on running the sample programs of slaveport in RCM4000.

asked Aug 1, 2014 in Rabbit Software by AISWARYA RAJ New to the Community (1 point)

0 votes

1 answer

Under what conditions does the Xbee PRO S2B retry transmisssion?

asked Jun 16, 2014 in ZigBee PRO Featureset (and legacy ZNet 2.5) by adnan.ashraf New to the Community (1 point)

0 votes

2 answers

XBee-PRO ZB (S2B) data transmission issue

asked May 29, 2014 in ZigBee PRO Featureset (and legacy ZNet 2.5) by Kirill New to the Community (4 points)

0 votes

1 answer

Sending data from Xbee end device in sleep mode

asked May 1, 2014 in RF Solutions and XBee by abdul New to the Community (0 points)

0 votes

2 answers

Unable to transmit using XBee and a microprocessor board

asked Mar 21, 2014 in DigiMesh Proprietary Mesh Networking by gbarne2 New to the Community (1 point)

0 votes

2 answers

Missing of data in the serial transmission from a PC to RCM4000.

asked Feb 25, 2014 in Rabbit Software by AISWARYA RAJ New to the Community (1 point)

0 votes

1 answer

digimesh SM=7 receiving data

asked Sep 10, 2013 in DigiMesh Proprietary Mesh Networking by dhipple New to the Community (3 points)

0 votes

0 answers

XBee pin state override normal Din/Dout transmission?

asked Jul 2, 2013 in RF Solutions and XBee by helium New to the Community (1 point)