Recent questions tagged xbee-pro-900hp

0 votes

1 answer

The selected firmware is not compatible with the radio module

asked Aug 20, 2021 in DigiMesh Proprietary Mesh Networking by riko_setiawan New to the Community (0 points)

0 votes

1 answer

XBee Pro 900HP Pin#7 / DIO11 / PWM1 not going low

asked Jun 22, 2021 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

0 answers

Creating and sending 0x11 packets in API mode using C (CW SDK)

asked Jan 19, 2021 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Serial console enabled/disabled setting on a Coordinator radio

asked Sep 29, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

printf functions in API mode for S3b 900HP giving trash

asked Aug 10, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

XBIB-U-DEV & PEMicro Universal Debugger - Chance of survival?

asked Jul 29, 2020 in RF Solutions and XBee by D2K New to the Community (14 points)

0 votes

1 answer

XCTU vs API pin configuration

asked Jul 27, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Values not being set at init when observed with Multilink

asked Jul 27, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

MultiLink firmware and detection problem

asked Jul 24, 2020 in RF Solutions and XBee by D2K New to the Community (14 points)

0 votes

0 answers

900HP Gateway as indirect messaging coordinator loses some messages (Route Not Found)

asked Oct 7, 2019 in DigiMesh Proprietary Mesh Networking by Garth_ESS New to the Community (0 points)

0 votes

1 answer

Very very low range with XBee-Pro 900HP

asked Oct 3, 2019 in RF Solutions and XBee by RWalmsley New to the Community (0 points)

0 votes

0 answers

Cannot syncrhonize an linear array of nodes in syncro sleep mode with XBee 900HP 200k in DM

asked Oct 2, 2019 in DigiMesh Proprietary Mesh Networking by XENPAUL New to the Community (3 points)

0 votes

1 answer

How do I use programmable XBee pro (with Serial bypass app installed) with an Arduino?

asked Aug 8, 2017 in DigiMesh Proprietary Mesh Networking by RoboNerd New to the Community (0 points)

0 votes

1 answer

I need to erase the app off of my programmable XBee

asked Aug 8, 2017 in DigiMesh Proprietary Mesh Networking by RoboNerd New to the Community (0 points)

0 votes

2 answers

How to read ultrasonic sensor echo pulse

asked Mar 24, 2017 in XBee Programmable Development by jbarham New to the Community (0 points)

0 votes

1 answer

Unable to communicate between two modules (XBee Pro 900HP-200K)

asked Oct 13, 2016 in DigiMesh Proprietary Mesh Networking by rsynoski New to the Community (0 points)

0 votes

1 answer

XBEE "XBP9B-DMST-002" Range Issue

asked Oct 7, 2016 in IEEE 802.15.4 by mohsinn New to the Community (2 points)

+1 vote

2 answers

Compatibility between XBee PRO 900HP and XBee SX modules

asked Jun 14, 2016 in DigiMesh Proprietary Mesh Networking by hassanjawad New to the Community (3 points)

0 votes

1 answer

What would be the best setup for my XBee 900HP network ?

asked Jun 11, 2016 in DigiMesh Proprietary Mesh Networking by brunoaduarte New to the Community (11 points)

0 votes

1 answer

PRO 900 and PRO 900HP Compatibility

asked May 3, 2016 in Multipoint Proprietary by dkramer New to the Community (0 points)