Recent questions tagged xbee-pro-s3b

0 votes

1 answer

Difference between 4 "Function Set" options for S3B XSC firmware?

asked Jan 13 in RF Solutions and XBee by L0uisc New to the Community (2 points)

0 votes

1 answer

How to configure the xbee api mode in UART for 3.3v logic MCUs?

asked Oct 14, 2021 in RF Solutions and XBee by elphmatt New to the Community (1 point)

+1 vote

1 answer

Can I remove the wire antenna and solder on an sma connector on an XBee-PRO® 900HP?

asked Jul 12, 2021 in RF Solutions and XBee by lazyf New to the Community (1 point)

0 votes

1 answer

XBee Pro 900HP Pin#7 / DIO11 / PWM1 not going low

asked Jun 22, 2021 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Define xbee s3b as transceiver

asked May 26, 2021 in RF Solutions and XBee by fareee New to the Community (0 points)

0 votes

1 answer

Relaying MODBus data via the S3B 900HP-programmable

asked May 12, 2021 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

0 answers

Creating and sending 0x11 packets in API mode using C (CW SDK)

asked Jan 19, 2021 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Xbee S3B 900HP change firmware from 200k to 10k datarate

asked Dec 30, 2020 in XCTU by legendkiller82 New to the Community (0 points)

0 votes

1 answer

S3B-900HP Programmable - topology diagrams

asked Dec 18, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

S3B 900HP - RAM allocation issues for an 1:N coordinator node architecture

asked Dec 5, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Serial console enabled/disabled setting on a Coordinator radio

asked Sep 29, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

0 answers

Can transmit_basic_frames be made to work with S3B/900HP programmable?

asked Aug 11, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

printf functions in API mode for S3b 900HP giving trash

asked Aug 10, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

900HP/S3B Programmable - out of the box expectations

asked Aug 3, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

XBIB-U-DEV & PEMicro Universal Debugger - Chance of survival?

asked Jul 29, 2020 in RF Solutions and XBee by D2K New to the Community (14 points)

0 votes

1 answer

XCTU vs API pin configuration

asked Jul 27, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

1 answer

Values not being set at init when observed with Multilink

asked Jul 27, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)

0 votes

2 answers

MultiLink firmware and detection problem

asked Jul 24, 2020 in RF Solutions and XBee by D2K New to the Community (14 points)

0 votes

2 answers

XBee S3B problem with communication between Arduino Uno and grove development board

asked Jul 23, 2020 in RF Solutions and XBee by brettv30 New to the Community (0 points)

0 votes

1 answer

XBee 900HP programmable - pull down & drive strength settings

asked Jul 15, 2020 in DigiMesh Proprietary Mesh Networking by D2K New to the Community (14 points)