COVID-19 Digi Technical Support Response x

Knowledge Base

What would you like to know?

To send a break to a serially attached device, you will telnet to the PortServer/Digi One device port: telnet (IP_of_Digi_unit) 2001 Where 2001 represents the port number 1, use 2016 for port 16... https://www.digi.com/support/knowledge-base/how-do-i-send-a-break-from-a-telnet-session Jul 06, 2017
The 'ser' variable, under Data Streams in Device Cloud, stands for Sensor State Error.@@This variable can have@two states:0 — sensor error1 — no errorSo what would cause it to go to 0?The 'ser' dat... https://www.digi.com/support/knowledge-base/what-would-cause-the-sensor-error-state-ser-to-go Jul 06, 2017
PortServer II setup:On 192.8.8.5 enter the following commands logged in as "root" on your PortServer II:Configure Port(s): #@ set port range=8 dev=mio #@ set flow range=8 ixon=off ixoff=off rts=... https://www.digi.com/support/knowledge-base/how-do-i-connect-two-lans-together-using-the-p-(1) Jul 06, 2017
Since 2012 September, shipping Digi Connect ME 4MB modules@(DC-ME4-01T-C) might have an updated flash chip, Micron M29DW323DB, which is@not supported by the old linux kernel 2.4.22 flash driver. Pr... https://www.digi.com/support/knowledge-base/shipping-digi-connect-me-4mb-modules-have-an-updat Jul 06, 2017
Below is the current list of Digi products with their respective capabilities to Unique password as well as support for Remote Manager. List of products where a unique password is required to logi... https://www.digi.com/support/knowledge-base/digi-remote-manager-and-unique-password-products-c Jul 22, 2019
Symptom: My modems disconnect on Digi ports when using Lotus Notes. @Cause: Hardware Flow Control is not enabled. Incorrect Modem MDM file@Solutions: Verify that hardware flow control is e... https://www.digi.com/support/knowledge-base/in-windows-nt-i-am-experiencing-modem-disconnectio Jul 06, 2017
In most cases, running a range test can be done by following the directions that come in XCTU or within the Quick Start Guides. With the 9XTend, that is not the case. This does not mean that you ca... https://www.digi.com/support/knowledge-base/how-to-run-a-range-test-with-the-9xtend-and-xctu-6 Jul 06, 2017
The event log is implemented as a ring buffer, and the allocated memory chunk is 64KB. Each log entry is actually variable in size, depending upon the amount of text in the message. For each entry,... https://www.digi.com/support/knowledge-base/event-log-size-in-digi-connectport-and-connect-wan Jul 06, 2017
Native Modem ConfigurationModem Configuration requires familiarity with the specific modem being used. While the following procedure is sufficient for most cases, it may be necessary to take additi... https://www.digi.com/support/knowledge-base/how-to-configure-modems-with-digi-portserver-and-d Jul 06, 2017
Socat allows to read/write data from a serial port and forward it through TCP/IP. With this feature you can implement serial to Ethernet or WiFi bridge on a Linux enabled embedded device.Example fo... https://www.digi.com/support/knowledge-base/serial-to-ethernet-or-wifi-bridge-with-linux-socat Sep 22, 2017
44 result(s) for Connect+IT+16