COVID-19 Digi Technical Support Response x

Knowledge Base

What would you like to know?

Digi International does not have an official adapter board, but users have created them in the past, such as:http://bansky.net/blog/2008/05/adaptor-board-for-digi-connect-me/ https://www.digi.com/support/knowledge-base/is-there-an-adapter-board-for-the-digi-connect-me Jul 06, 2017
Please see the ME recovery guide for this:https://ftp1.digi.com/support/images/connect/intkit/docs/Connect_Mfg-DiagsMode.pdf @ In case you don@t have a Digi development board to perform the recov... https://www.digi.com/support/knowledge-base/connect-me-s-recovery-instructions Jul 06, 2017
This article will describe how to mount the Digi Connect ME or WiME onto a customers product with proper grounding. The following text below is Digi''''s best practice for grounding the ME or WiME.... https://www.digi.com/support/knowledge-base/what-is-the-recommended-method-of-grounding-the-me Jul 06, 2017
OverviewMany Digi products contain and use the RomPager by Allegrosoft web server technology. It has come to our attention that this embedded web server, which is used for management of our devices... https://www.digi.com/support/knowledge-base/embedded-net-os-modules-rompager-evaluation-of-sec Jul 06, 2017
Modules running Plug @ Play Firmware onlyFunctionalitCapabilitiesDC-ME-01T-S@@@ DC-ME4-01T-SDC-ME-Y402-SHardware@ @ @ @@CPUARM7 NS7520 55MHzARM7 NS7520 55MHzARM9 NS9210 75MHz 4KB cache@... https://www.digi.com/support/knowledge-base/comparison-on-digi-connect-me-me-9210 Jul 06, 2017
Hardware reference manual http://ftp1.digi.com/support/documentation/90001247_C.pdf statement about RESET:Pulling pin 8 low with an open drain driver will force the module into a hard reset state. ... https://www.digi.com/support/knowledge-base/connect-me-and-me-9210-reset-pin-recommendations Jul 06, 2017
With the Digi powered off connect pins 2 @ 3 @of the P12 pin header. @Then power the Digi up and wait for about a minute. @You can then power the device off, remove the connection from pins 2 @ 3 a... https://www.digi.com/support/knowledge-base/reset-an-me-or-wime-back-to-factory-defaults-while Jul 06, 2017
OverviewMany Digi products contain and use the RomPager by Allegrosoft web server technology. It has come to our attention that this embedded web server, which is used for management of our devices... https://www.digi.com/support/knowledge-base/embedded-nds-rompager-evaluation-of-security-vulne Jul 06, 2017
If you use timezone settings with LxNETES-2.3 uClinux 2.4.22 ConnectCore 7U (unc20) or Digi Connect ME you might observe that daylight saving time is switched on a wrong day at least in 2012 (maybe... https://www.digi.com/support/knowledge-base/connectcore-7u-unc20-or-digi-connect-me-running-lx Jul 06, 2017
While compiling LxNETES-2.3 for Digi Connect ME getting: make[1]: boothdr: Command not found make[1]: *** [linux.netos] Error 127 make: *** [linux/linux.netos] Error 2 Make sure you have instal... https://www.digi.com/support/knowledge-base/while-compiling-lxnetes-2-3-for-digi-connect-me-ge Jul 06, 2017
46 result(s) for Digi+Connect+ME