Raw partition update
update command simplifies the task of updating a partition of the eMMC by performing the following operations:
Download the required firmware image files from the specified media to RAM memory.
Retrieve and check information (offset, size) of the partition to update.
Write the firmware image to the partition.
Read back and verify the written firmware image.
=> help update update - Digi modules update command Usage: update <partition> [source] [extra-args...] Description: updates (raw writes) <partition> in $mmcdev via <source> Arguments: - partition: a partition index, a GUID partition name, or one of the reserved names: uboot - [source]: tftp|nfs|mmc|ram - [extra-args]: extra arguments depending on 'source' source=tftp|nfs -> [filename] - filename: file to transfer (if not provided, filename will be taken from variable $<partition>_file) source=mmc|usb -> [device:part] [filename] - device:part: number of device and partition - filename: file to transfer (if not provided, filename will be taken from variable $<partition>_file) source=ram -> [image_address] [image_size] - image_address: address of image in RAM ($loadaddr if not provided) - image_size: size of image in RAM ($filesize if not provided)
Example 1: Update partition named myname with file
test.img downloaded from TFTP:
=> update myname tftp test.img
Example 2: Update partition named linux in the eMMC of the module using default filename (determined by variable
$linux_file) reading the file from a FAT partition on the uSD card:
=> update linux mmc 1:1 fat
Check the default partition names at eMMC layout.
Customization using environment variables
You can customize the behavior of the update command through its parameters and also by using the following environment variables:
RAM address where the firmware image file to use for the update is downloaded.
RAM address where the firmware image is read back to, for verification.
U-Boot automatically sets this variable to a RAM address halfway through the available RAM, starting at
Image file names
Default image filename to use for updating the bootloader (if no filename is passed as parameter).
A variable of this form will contain the default filename to use for updating the partition named <partition-name>.
For example, the variable containing the default filename for a partition named recovery would be called
Target MMC device index to write the firmware to.
For "u-boot" partition updates, target MMC partition index to write the firmware to.
Updating the bootloader
You can use the
update command to manually update the bootloader in the eMMC.
For example, to update from TFTP using the default filename (in variable
=> update uboot tftp
|Writing an invalid bootloader file may lead to the target not booting.|
Digi releases U-Boot updates from time to time to fix problems or add new functionality. Much of the custom functionality added to U-Boot depends on environment variables and scripts that may have new values in newly released versions. Digi recommends that you reset the environment to its defaults after upgrading U-Boot:
=> env default -a
This resets the whole environment, with the exception of protected variables (like the MAC addresses). After resetting the environment, you may need to adjust your manufacturing or boot scripts to accommodate changes in the default environment, like new or modified scripts, variables, and default filenames.
See U-Boot files by variant to verify which U-Boot binary you need.
On-the-fly update mechanism
The normal update command first transfers the file completely from a media into the RAM memory. Then it writes the file from RAM into the eMMC. Occasionally, the firmware files used to update a certain partition are very large, maybe larger than the available RAM of the platform. In that scenario, the update strategy must:
Transfer a chunk of the file from the specified media to the RAM memory.
Write the chunk to the partition and verify the written data.
Repeat the process until the file has been completely written.
We call this mechanism on-the-fly update.
The on-the-fly update mechanism can only work when updating from TFTP source and is only recommended for updating very large images. Note that if there is any problem during the transmission of the file, the partition is left partially written (compared to the standard update where, if the transmission fails, the partition remains untouched).
For security reasons, the on-the-fly update mechanism is automatically disabled when updating the bootloader.
You can activate the on-the-fly update mechanism by setting the variable
yes, and then using the update command normally.
If the variable
$otf-update is not defined, the
update command may automatically activate the on-the-fly update mechanism if the size of the partition to update is larger than the available RAM to hold the firmware.
(The TFTP protocol does not indicate the size of the file being transferred.)
The on-the-fly update mechanism pauses the TFTP transfer while it writes each chunk to the eMMC, and resumes after reading back and verifying the written data. For this reason it may not work with all TFTP servers. Be sure to check that your TFTP server has a large enough timeout so that it doesn’t cancel the transfer due to not receiving the client’s ACKs in time while the device is writing and verifying. Also, disable any mechanism that sends packets without waiting for the client’s ACKs (like anticipation window) which may not always work with the on-the-fly update mechanism.
Update files within partition
updatefile command simplifies the update of files in a partition’s file system.
While the standard update command writes raw data to the eMMC, the
updatefile command uses U-Boot file system support to write files to a formatted partition by performing the following operations:
Download the required file from the specified media to RAM memory.
Write the file to the partition’s file system.
=> help updatefile updatefile - Digi modules updatefile command Usage: updatefile <partition> [source] [extra-args...] Description: updates/writes a file in <partition> in $mmcdev via <source> Arguments: - partition: a partition index or a GUID partition name where to upload the file - [source]: tftp|nfs|mmc|ram - [extra-args]: extra arguments depending on 'source' source=tftp|nfs -> [source_file] [targetfile] [target_fs] - source_file: file to transfer - target_file: target filename - target_fs: fat (default) source=mmc -> [device:part] [filesystem] [source_file] [target_file] [target_fs] - device:part: number of device and partition - filesystem: fat (default)|ext4 - source_file: file to transfer - target_file: target filename - target_fs: fat (default) source=ram -> [image_address] [image_size] [targetfile] [target_fs] - image_address: address of image in RAM ($loadaddr if not provided) - image_size: size of image in RAM ($filesize if not provided) - target_file: target filename - target_fs: fat (default)
Example 1: Update the
newkernel.bin file from TFTP to linux FAT partition:
=> updatefile linux tftp newkernel.bin
Example 2: Update the
newkernel.bin file from uSD card FAT partition 3 to linux FAT partition and save it with filename
=> updatefile linux mmc 1:3 fat newkernel.bin myImage-test fat
Limitations and cautions
Only FAT and EXT4 file systems are supported.
Files can be overwritten but cannot be deleted.
File system support does not check for available space.
|Writing a file on a file system that does not have space for it may corrupt the entire file system.|