This section helps you set up your ConnectCore device to see Storyboard in action.

The goal of this section is to have a Storyboard demo application running in your device. This application includes three different demos:

  • Electrical vehicle charger demo

  • Robot arm demo

  • Medical demo

Follow these steps to get started using the Crank Storyboard demo with your ConnectCore 6UL SBC Pro.

Requirements

  • A ConnectCore 6UL SBC Pro

  • The Crank prebuilt images

  • LVDS or HDMI display for the graphical user interface

  • A mouse to work in the graphical user interface

1. Download the firmware

Download the firmware images from the following location: https://ftp1.digi.com/support/digiembeddedyocto/4.0/r5/images/ccimx6ulsbc/ccimx6ulsbc-crank-installer.zip

The Crank demo image includes:

  • Storyboard Engine. The target-specific executable that loads the model generated by Designer and starts the execution of the state machine. See What is Storyboard?.

  • A Storyboard application created and exported with Storyboard Designer. This application is configured to be launch at startup.

2. Program the Crank demo image

Digi recommends you use the Universal Update Utility (UUU) through a USB connection to your development PC to program the images.

  1. Decompress the zip file in a directory of your choice.

  2. Set up your computer.

    1. Download the latest Universal Update Utility (UUU), a software tool from NXP.

      UUU version should be 1.5.11 or higher.

    2. Place the uuu executable in a directory in your PATH, such as /usr/bin.

    3. Install udev rules to allow any user to run uuu to access the USB port:

      $ sudo sh -c "uuu -udev >> /etc/udev/rules.d/70-uuu.rules"
$ sudo udevadm control --reload

  3. Connect a micro USB cable to your development PC and the other end to the target USB OTG connector.

  4. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

     1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
    		U-Boot dub-2020.04-r6.1 (Sep 19 2023 - 07:12:31 +0000)

CPU:   i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 32C
Reset cause: POR
I2C:   ready
DRAM:  256 MiB
MCA:   HW_VER=1  FW_VER=1.19
PMIC:  PFUZE3000 DEV_ID=0x30 REV_ID=0x11
NAND:  256 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Model: Digi International ConnectCore 6UL SBC.
ConnectCore 6UL SOM variant 0x06: Industrial Ultralite 528MHz, 256MB NAND, 256MB DDR3, -40/+85C, Wireless, Bluetooth
  Board version 3, ID 135
Boot device:  NAND
Net:   FEC0 [PRIME]
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
=>
    Information in the console log may vary.

  5. On the target, in U-Boot, execute the following command:

    => fastboot 0

  6. On your development PC, change to the directory where you extracted the ZIP file:

    $ cd <zip-folder>

  7. To program the demo image, run:

    $ ./install_linux_fw_uuu.sh -i dey-image-crank

  8. Once the firmware is installed, the device boots automatically. The default username is root with no password.

3. Test the Crank Storyboard demo

The Storyboard demo is automatically launched on boot.

Select any of the three different demos and interact with it:

  • Electrical vehicle charger demo

  • Robot arm demo

  • Medical demo

You can develop your own applications with Storyboard Designer, see Getting started with Storyboard.

To build your image with Storyboard Engine and applications, see Create a Crank image.